Little FOCer  Rev3.1  ESC Electric Speed Controller - BYOH
Little FOCer  Rev3.1  ESC Electric Speed Controller - BYOH
Little FOCer  Rev3.1  ESC Electric Speed Controller - BYOH
Little FOCer  Rev3.1  ESC Electric Speed Controller - BYOH
Little FOCer  Rev3.1  ESC Electric Speed Controller - BYOH
Little FOCer  Rev3.1  ESC Electric Speed Controller - BYOH

Little FOCer Rev3.1 ESC Electric Speed Controller - BYOH

Regular price$300.00
/

  • $15 Flat Rate Shipping (Domestic Only)
  • Low stock - 6 items left
  • Inventory on the way

*Usually ships in 1-2 business days.

Little FOCer Rev3.1 ESC Electric Speed Controller BYOH (Bring your own Heat-sink version)

  • The Little FOCer without a heat sink
  • Uses Vesc based firmware
  • DC Input 12 Gauge wire to XT60  Male
  • Phase Output 12 Gauge wire to 4mm Female Bullet connectors
  • On board IMU for balance applications 
  • Integrated Bluetooth NRF 52840 
  • DRV less design
  • Sophisticated fault detection for over-current, over-voltage, gate drive errors, and more
  • Easy On/Off capability with latching switch of choice
  • ESD Protected IO
  • 72mm x 84mm PCB footprint
  • ADC1 and ADC2 internally equipped with 10k Ohm pulldown resistors. 

The capacitors and JST connectors' are mounted on the opposite sides of the mosfets so that the motor controller can be mounted to a metal plate or other custom heat sink solution.  This is typically the best option for fitting inside the controller box of a balance board.

New features in  Rev3:

  • Increase current limits
  • support for phase filters
  • ASS support (Advanced Sensorless Startup)

 

Specification Value
 Nominal Input Voltage 28V to 72V (8s to 20s Lithium Ion)
Recommended Lower voltage limit 24V
Absolute Maximum Operating Voltage 84V
Battery Current Consumption

Off=500µA

Idle< 0.8W

Max (ext.) = 100A

Peek Phase Current 250A
Peak Efficiency 95% or greater
PET PWM switching frequency range 10kHz to 60kHz (Center Aligned PWM)
Minimum recommended motor phase to phase inductance 10µH
Supported Motor Types BLDC and DC motors
Input Capacitance 602µF
Operating Ambient Temperature Range -20C to 50C
Storage Temperature Range -35C to 85C
Thermal Cutback The controller linearly reduces maximum output current when the internal controller temperature is above 80C. Complete cutoff at 100C, the control board over-temperature threshold
Communication Protocols 

1xCAN

1xUART 

1xBlutooth Low Energy

Gyroscope

On board IMU

Management Interfaces

USB Type-C

Bluetooth

Management Software

VESC 6 open source project compatible 

 

 

The Little Focer V3 is based upon the VESC®-Project. VESC is a registered TM, owned by Benjamin Vedder

 

Order Processing Time
We require 2-3 business days to process and pack your order. This means that your order will typically ship out within 2-3 business days after it has been placed. Please note that our processing time may be longer during peak shopping periods, sales, or holidays.

Shipping Rates and Methods
We currently offer standard shipping to the United States and select international destinations. Our shipping rates are calculated based on the weight and destination of your order, and will be displayed at checkout.

Delivery Times
While we strive to provide accurate delivery estimates, we cannot guarantee delivery dates or times. Delivery times will depend on your location, the shipping method you select, and the carrier's delivery schedule. Please note that delivery may be delayed due to factors outside of our control, such as weather, customs clearance, or carrier delays.

Tracking Your Order
Once your order has shipped, you will receive a shipping confirmation email with a tracking number. You can use this tracking number to track your package online through the carrier's website.

International Shipping
For international orders, please note that the recipient is responsible for any customs fees, import duties, taxes, or other fees that may be imposed by their country's customs office.

Returns and Refunds
Please refer to our Returns and Refunds policy for information on how to return or exchange your order.

If you have any questions about our shipping policy or your order, please contact us at support@makerspev.com.

TOP NOTCH PEV PRODUCTS

Makers PEV strives to be the best in the industry when it comes to open source EV creation.

You may also like


Recently viewed

FAQs

Though we are working hard to make this as easy as possible with no soldering and programming needed this is ultimately still a DIY solution.

The choice in parts and settings are still up to the user to decide. This allows for great creativity but does require some knowledge. If you are new, please research existing builds and settings before proceeding!

The Little FOCer is simply a motor controller. It was created to run any electric motor.

Yes but the pint/GT uses proprietary connectors therefore will need some DIY in order to make it work.

You can use any battery that fits in your build up to 20s! At this time there are a few manufacturers that make compatible upgraded batteries. 2 that we would recommend include Z Battery Solutions and The Board Garage.

Pev.dev is the best collection of information at this time and I would recommend searching there for common issues but if you have more specific needs feel free to reach out to us at support@makerspev.com

The BMS choice is ultimately up to the user but a few popular options at the moment are ZBMZ, the ennoid and changing an xr/pint bms to charge only.

The Makers PEV BMS is in the works and coming soon.

Yes we ship anywhere we can from the United States. International shipping rates will apply and are not included in our $15 flat rate shipping.

Though most of the connectors from an XR controller can be reused it will require quite a bit of DIY and is significantly harder.

The only part that is not compatible is the momentary switch on the XR. The Little FOCer uses a latching switch.

No, our product replaces it completely and does not work with it in any way. You can choose to use either the Littler FOCer or your FM controller, but you cannot use them together.

No, at this time we are here to support people in their own builds and provide the equipment needed to do so.

VESC is the software that the Little FOCer hardware runs on similar to how Linux is the operating system for many different computers.